1/8 DIN Temperature Controller Heat/Cool Controllers


1/8 DIN, Temperature Controller, Heat/Cool ControllersFuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers are designed to provide precise control with a quick and easy set up procedure. SMT and microprocessor technology provides all these features plus reliability and economy. LED index indication allows full viewing and selection of parameters.

The dual display allows set point and process value visibility at all times. An advanced software algorithm automatically calculates all PID parameters to eliminate complicated manual tuning efforts. Automatic tuning can be bypassed if manual tuning is preferred. An open-loop, manual mode can be initiated if the sensor fails. Front panel electronic calibration sensor linearization self-diagnostic capabilities and cold junction compensation are all performed by the single chip microprocessor. The in-panel depth is only 2-1/2".

FuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers Features:

• Automatic tuning of PID parameters
• Selectable input
• Dual heating and/or cooling outputs with 2 alarms
• ºF or ºC display. Dual display. Sealed mylar front panel
• Security code protection, automatic manual mode operation
• All control parameters adjustable from front panel
• 3 year warranty. 2-1 /2" in panel depth

FuzyPro 1 /8 DIN Temperature Controller Heat/Cool Controllers Specifications:

INPUT
Thermocouple Type J,K.T.B.E,R,S,N selectable
RTD PT 100ohm (DIN or JIS)
Linear -10-60mV Configurable input or voltage or current
Display Temperature or engineering units
OUTPUTS Single output with 2 optional independent alarms
Heating and cooling outputs with 2 optional Alarms
Relay SPST relay rated 3A, 240V maximum resistive load
Pulsed Voltage 32VDC,2OmA maximum ohms
Current 4-20mA,0-20mA maximum load 500 ohms
Voltage 0-10V minimum load 500K ohms
Alarms 8 selectable modes each alarm
SPST relay(s) rated 2A, 240V maximum resistive load.

CONTROL FEATURES
Temp Range Selectable Set Point: -1999-3182F/-1128-1750C
Alarm Set Point Full Range Adjustable
Control Modes Controls can be configured as On/Off Proportional (P)
Proportional with manual reset                             
Proportional/Integral (PI) Proportional                             
Derivative (PD)                             
Proportional/Integral/Derivative (PID)                             
Heating and Cooling Proportional Band: 0-100% of span
Integral (Reset) 0-3600 seconds
Derivative(Rate) 0-1000 seconds
Anti-Reset Wind-up Inhibits integral action outside of proportional band.
Cooling Adjustable deadband from-10 to + 10% of cooling proportional band
Manual Mode Configurable as open loop control should sensor no longer function
Cycle Time 0-120 seconds
Sensor Break Protection Configurable status of control and alarms
Control Action Selectable-Direct action for cooling Reverse action for heating

INDICATION
Display 4 digit red 5/8" LED Process Value Display.
Green 1.2" LED Set Value display
Selectable decimal placement for normal or high resolution display
Example 0000, 000.0, 00.00 or 0.000
F/C Selectable with 2 LED indicators
Sample Rate 250 milliseconds
Power Supply 90-26OVAC, 50/60Hz Consumption: less than 5VA
Data Retention l0 years (EEPROM)
Control Stability + -0.15% of full scale
Accuracy + -0.25% of range: + -1 c or 0.5C in high resolution
Cold Junction Compensation 0.1% ambient
External Resistance 100 ohms maximum
Common Mode Rejection 120dB
Normal Mode Rejection 60dB
Input Impedance 10M ohms
Operating Temperature 14-122ºF (-10-50ºC)
Humidity 0-90% RH(non-condensing)
Insulation 20M ohm minimum (5OOVDC)
Breakdown 2OOVAC, 50/60Hz 1 minute
Vibration 10-55Hz amplitude 1 mm
Shock 200m/c (20g)

1/8 DIN Temperature Controller Heat/Cool Controllers Brochure
1/8 DIN Temperature Controller Heat/Cool Controllers Manual


For Quick Delivery From Stock Call
CANADA & USA TOLL FREE: 1 - 800 - 279-9912

 

Site Design - Panther Marketing & Design
Back to Top